Code

Quantity

Price

Item

Description

More info?

SM1

1

80.00

14 lever signal frame kit

Cast brass pre-drilled 4" levers, 18thou floor plate & fittings; solder built kit

SM2

1

45.00

7 lever signal frame kit

Smaller version of the above, to improved specification

SM2/1

1

3.75

SM2 upgrade kit

Lever spacers and catch handle nuts/screws/washers to give more robust and easier assembly

SM3

1

4.50

Signal lever & return spring

Cast brass lever & spring as used in SM1 & 2

SPR

1

0.25

Return spring

Spare tension springs as used in SM1-3 above

SM4

5m

5.00

Wire & tube control kit

5m nickel silver 24swg wire & PTFE tubing with instructions

SM5

1

2.50

Manual signal operating mechanism

Etched brass, wire or rod operated; instantly removable from the baseboard for transport etc.

SM6/1

1

8.50

Latching solenoid

Magnets hold the plunger at each end of its travel - only draws current for movement. 12V dc

SM6/2

1

1.50

DPDT switch

Passing contact switch for SM6/1

1

6.50

Solenoid

Continuously rated 12V dc solenoid for point and signal operation – simple on-off switch needed

SM8

2

2.50

Moulded nylon cranks & bases

Nominal 1"x 1" throw; complete with 6BA bolts, nuts & washers

SM9

4

1.50

Moulded nylon snap joints for SM8

To fit 1.6mm/16swg/1/16" rod; quick-release joint; enables baseboard joints to be crossed

SM10

36"

1.00

1/16" brass rod for use with SM8/9

Brass rod for indoor and outdoor use (exhibition sales only)

SM11

1

11.50

Signal motor

Damped twin solenoid signal motor; 12V dc or ac operation (by Viessmann)

SM11/1

1

0.80

SPDT switch

Changeover switch for SM11

MMN-U-S

1

17.95

Signal servo unit & control module

Gives prototypical slow pull off and bounce back to danger (by Embedded Controls).

FULGM

1

9.50

Fulgurex turnout motor

TORTM

1

12.50

Tortoise turnout motor

PM1

1

4.35

Seep point motor

Twin solenoid design, 12-25V ac or dc working voltage, with crossing polarity switch

PM2

1

4.10

Seep point motor

As PM1, but without the crossing polarity switch

PM4

1

5.10

Seep point motor

As PM1, with self-latching operation for hand-built turnouts

CDU

1

11.50

Capacitor discharge unit

For crisp, reliable operation of solenoid point motors; prevents coil burn-out

Code

Quantity

Price

Item

Description

More info?

1001

1

2.75

Universal point lever

3/16" throw in each direction; size 19x11mm

1001T

3

7.50

Universal point lever

As above, but in a triple pack

1002

6

2.30

Angle cranks

Individual mounting bases; throw adjustable up to 7mm

1005

6

1.75

Omega wires

For taking up excess throw in point and signal mechanisms; 44mm long

1006

6

1.75

Wire snaps

For attaching omega wires to SM4 operating wire

1008

1

9.95

4-way lever frame

3/16", 1/4" & 5/16" throw on each lever; 37x36mm footprint

1009

1

13.95

6-way lever frame

As 1008, but 49mm wide

1010

1

15.95

6-way lever frame

As 1008, but 63mm wide

1011

10

2.50

Large angle cranks

Etched brass, throw adjustable between 5 and 14mm

1012

6

2.30

Vertical angle cranks

Similar to 1002, but with right-angle bases for screwing to baseboard underside

1013

10

1.30

Peco point couplers

To couple 1001 universal point levers to Peco points, via 1005 omega wires